Screen-Mounted Gravity Phone Holder for BYD SEALION 7 (2024-2025) – For 15.6-inch or 12.8-inch Screen

The SEALION 7 gives you a huge center screen and nowhere sensible for your phone. This holder borrows the strongest structure on the dashboard — the screen itself — and parks your phone right beside it, at eye level, in a gravity cradle you work with one hand.

Vent clips chew on air vents and wobble. Suction cups let go on hot days. This mount is built for one dashboard only: a model-specific bracket reaches behind the SEALION 7's center display and locks onto the back of the screen housing, positioning the cradle at the driver's side of the screen — the exact spot your eyes already visit. Drop the phone in and gravity does the clamping. No buttons, no springs to fight, no magnets to line up.

• The phone sits where your eyes already are — beside the navigation display, at dash-top height, in portrait. A glance at your phone's directions is the same glance you give the car's own screen, not a dive down to a vent or the console.
• Gravity clamping, one hand, one second — set the phone into the cradle and its own weight drives the two padded side arms closed while the twin bottom feet take its weight. To leave, lift the phone straight up and the arms open. It works the same on the hundredth use as the first, with nothing to wear out or switch on.
• Rock-solid because of where it mounts — the bracket is clamped to the screen housing, not clipped to a vent slat or stuck to glass. The phone is held on both sides and underneath, and it stays composed over speed bumps, potholes and rough country roads.
• Your vents and dash stay untouched — full airflow from every vent, no adhesive pads on the dashboard, no suction ring on the windscreen, and nothing in front of the car's own display: the cradle sits beside the bezel, not over the screen.
• The charging port stays open — the two bottom feet leave a gap at the center of the cradle, so a charging cable plugs into the mounted phone exactly where it always does.

• 15.6-inch Screen — the bracket sized for the SEALION 7's 15.6-inch rotating DiLink display, the large screen fitted to the great majority of cars. If your center screen is the big unit that dominates the dashboard, this is your version.
• 12.8-inch Screen — the bracket sized for cars fitted with the smaller 12.8-inch center display. The arm length and hook geometry are matched to that screen's housing so the cradle lands in the same position beside the bezel.

The two versions are not interchangeable trim options — the bracket is dimensioned around the screen it grips. Your screen size is the diagonal of the display; it is printed in your car's specification and is the first thing you see in the settings menu. Order the version that matches it and the cradle sits flush beside the screen, as the installation photo shows.

• Bracket: a flat arm runs behind the display and ends in a hook with a round locking knob — hook it over the screen housing, seat the arm, tighten the knob, and the mount is part of the dashboard.
• Cradle: gravity linkage with two round padded side arms and twin bottom feet; glossy face plate with BYD lettering.
• Contact points: smooth molded surfaces against the screen housing and padded arms against the phone — firm grip, no marks.
• Orientation: portrait phone position beside the driver's side of the screen, as pictured in the fitted car (a left-hand-drive SEALION 7).

• Vehicle: BYD SEALION 7 (also sold as Sea Lion 07 EV)
• Model years: 2024 and 2025
• Screen: choose 15.6-inch or 12.8-inch to match your car's center display
• Position: mounted behind the center screen, cradle beside the driver's side of the display
• Phones: standard smartphones in portrait, including large-screen models in slim cases

1. Offer the bracket up behind the center screen on the driver's side and hook it over the back of the screen housing.
2. Seat the arm flat along the rear of the display and tighten the round locking knob until the mount is solid.
3. Drop your phone into the cradle — the side arms close around it under its own weight. Lift it straight up to take it with you.

• Contents: 1 × screen-mounted phone holder (bracket + gravity cradle) for BYD SEALION 7
• Mounting: hook-and-lock bracket on the back of the center screen housing; no adhesive, no suction, no vent clip
• Cradle type: gravity auto-clamp — side arms + bottom feet, one-hand in and out
• Versions: for 15.6-inch screen / for 12.8-inch screen
• Color: black
• Charging while mounted: bottom cable gap left open between the feet

Which screen size do I have?
Measure the display diagonally, corner to corner, or check the car's specification sheet: SEALION 7 cars carry either the large 15.6-inch rotating display — by far the most common — or a 12.8-inch display. Order the version that matches; the bracket is sized to the screen housing, so the two are not interchangeable.

Does it shake or drop the phone on rough roads?
No. The mount's stability comes from its fixing: a bracket clamped to the screen housing rather than a clip hanging off a vent. The phone itself is gripped on both sides by the gravity arms and carried on the bottom feet, so bumps load the cradle in the direction it is strongest. It stays composed where vent clips give up.

Does it cover any of the car's screen?
No. The cradle sits beside the display, beyond the bezel — the installation photo shows the full DiLink screen in use with the phone mounted alongside it. Nothing you tap or read on the car's display is hidden.

What happens when I rotate the center screen?
The holder is fixed to the screen, so it turns with it. It is designed around the screen's horizontal working position — the orientation the car uses for driving — so run the display in landscape while the holder is fitted, and your phone stays upright in portrait beside it.

Does it work with a phone case?
Yes, with standard slim and medium cases — the gravity arms close on whatever width you drop in, from compact phones to large-screen models. Very thick rugged or wallet-style cases can exceed the depth of the bottom feet; slim cases are the natural match.

Can I charge the phone while it is mounted?
Yes. The cradle's two bottom feet leave the center of the phone's bottom edge open, so your charging cable plugs straight in while the phone is held. There is no charger built into the holder itself — it is a mechanical gravity cradle, with nothing electronic to fail.

Which model years does it fit?
The 2024 and 2025 SEALION 7. The bracket is shaped around those cars' center screen housing, and this listing covers those model years.

Standard worldwide shipping is $9.90 USD on orders below $29.90 USD. Orders of $29.90 USD or more ship free with standard shipping. Return requests can be submitted within 30 days after delivery — see our Returns & Refunds policy for the full terms.

BYD SPOT is an independent accessories retailer and is not affiliated with, endorsed by, or sponsored by BYD Company Limited. Vehicle names and trademarks are used solely to identify product compatibility.